Page 1 of 2

FS Force and P3D V4

Posted: Sun Jun 18, 2017 2:50 pm
by Emile
Hello,
FS Force is installed and seams to work BUT all my aircrafts are running to left on the runway and taking off also the left.
I have to correct a lot with my FF stick. :oops:

Any recommendations.

I did NOT have this with the V3 P3D.
Thanks in advance

Re: FS Force and P3D V4

Posted: Mon Jun 19, 2017 9:10 am
by RussDirks
If you look in the external view, or the virtual cockpit, is the rudder hard left?

Re: FS Force and P3D V4

Posted: Tue Jun 20, 2017 10:31 am
by Emile
Hello,

I do not known what to look at.
I have changed the Calibration Rudder in P3D V4.
Seams better for runway and takeoff.

Is my change a good one?
Thanks in advance

Re: FS Force and P3D V4

Posted: Tue Jun 20, 2017 10:57 pm
by RussDirks
That looks fine. Are you saying everything is normal now?

Re: FS Force and P3D V4

Posted: Fri Jun 23, 2017 3:11 pm
by Emile
Hello,
NO it is not solved, I have less "going to the left" but I need to compensate a lot ...
I do not know what to do to solve it totally.

PS This on ALL Aircrafts

Recommendations?
thanks in advance

Re: FS Force and P3D V4

Posted: Sat Jun 24, 2017 1:35 am
by RussDirks
I know you said you calibrated your joystick, but we need to make sure the physical joystick is sending correct signals to the simulator. Please follow these steps:
  1. Start a flight and just leave the aircraft sitting on the tarmac.
  2. Make sure your FF stick is centered.
  3. Look down in the virtual cockpit at the rudder pedals. Are they centered?
  4. Switch to outside view by pressing the "S" key.
  5. If necessary, swivel the view so you can see the rudder of the aircraft. Is it centered, ie. in the neutral position?
  6. Are the other control surfaces also centered? Ailerons? Elevator?

Re: FS Force and P3D V4

Posted: Sat Jun 24, 2017 2:27 am
by Terrydew
You might also want to check the weather settings. Set to clear day and check to see wind a 0.

Re: FS Force and P3D V4

Posted: Sun Jun 25, 2017 3:26 pm
by Emile
Hello,

I made a test WITHOUT FSForce (exit in the addons) and I do not have this behavior.
Aircraft not going to the left ...on taxiway, runway and takeoff... :oops:


I do not fly with VC only with 2D panels

Re: FS Force and P3D V4

Posted: Sun Jun 25, 2017 7:49 pm
by Emile
Hello,


Forget this ...
IT IS NOT CORRECT ...

"I made a test WITHOUT FSForce (exit in the addons) and I do not have this behavior.
Aircraft not going to the left ...on taxiway, runway and takeoff... " :roll:

Re: FS Force and P3D V4

Posted: Mon Jun 26, 2017 10:53 pm
by RussDirks
RussDirks wrote:If you look in the external view, or the virtual cockpit, is the rudder hard left?
Emile wrote:I do not known what to look at.
RussDirks wrote:
  1. Start a flight and just leave the aircraft sitting on the tarmac.
  2. Make sure your FF stick is centered.
  3. Look down in the virtual cockpit at the rudder pedals. Are they centered?
  4. Switch to outside view by pressing the "S" key.
  5. If necessary, swivel the view so you can see the rudder of the aircraft. Is it centered, ie. in the neutral position?
  6. Are the other control surfaces also centered? Ailerons? Elevator?
Emile wrote:I do not fly with VC only with 2D panels
???

I think there is a misunderstanding here. I'm not asking you to make a permanent change to the way you fly with flight simulator, I am simply asking you to perform a one time sequence of steps to help diagnose the problem with your joystick. Surely you can do that, can't you? If the airplane you regularly fly doesn't have a VC, for the purposes of these steps, switch to one that does, like the default C172. We're trying to determine if the left pull you experience is hardware related or software.

Re: FS Force and P3D V4

Posted: Thu Jun 29, 2017 10:33 pm
by Emile
Hello,
I have made some screenshots BUT ALL ARE TOO BIG , I need to reduce the size ...
1/ Tail 1 = at start the aircraft is on the runway and the TAIL is already to the left
2/ Rudder For me the rudder seams good.

I will come back when the screenshots are smaller...

Re: FS Force and P3D V4

Posted: Thu Jun 29, 2017 10:41 pm
by Emile
Hello,
I also made a movie using my GSM showing the behavior of aircraft stick when I move my FFb 2 stick. I will try too add a link

Re: FS Force and P3D V4

Posted: Thu Jun 29, 2017 10:46 pm
by Emile

Re: FS Force and P3D V4

Posted: Fri Jun 30, 2017 10:52 pm
by RussDirks
Well, that definitely explains why your aircraft is pulling to the left. Your joystick may be defective. It is probably sending out a constant hard-left signal even though you are not twisting the handle. I think you said you already tried calibrating, but you might want to try it again, paying special attention to the Rz-Axis (twisting the joystick handle). If calibrating doesn't help, there's not much you can do. Although ... I recently heard from a customer who was experiencing a very similar problem. He ended up taking the joystick apart and found a wire that had broken off. After soldering it back in place, it worked perfectly! Who knows. Maybe you can fix it.

Re: FS Force and P3D V4

Posted: Tue Jul 04, 2017 1:19 pm
by Emile
Hello,
The "left" turn is solved after , following your suggestion, changing the calibration in P3D V4 HF1.
I still need your help concerning the back ailerons when I "fly" these are "vibrating?"

Which calibration must I try to change (see screenshot) X Axis, Y Axis, ....

Thanks in advance