getting G940 from Santa ....

Discussions and general chat

Moderator: RussDirks

Post Reply
krswen
Posts: 4
Joined: Mon Dec 21, 2009 7:35 am

getting G940 from Santa ....

Post by krswen » Mon Dec 21, 2009 7:52 am

Russ, did you get an evaluation unit from Logitech yet? I plan to use it for FSX, SF2 and Falcon4 AF and would like the benefit of your experience as a starting point.

krswen
krswen

RussDirks
Site Admin
Posts: 696
Joined: Sat Sep 13, 2003 1:18 pm
Location: Chilliwack, Canada

Post by RussDirks » Mon Dec 21, 2009 8:58 am

They said they were going to send me one, but there was some mix up, and it never got sent. After waiting awhile I finally sent them a reminder, so now apparently one is on the way. I'll post a review once I get a chance to use it.
Russel Dirks
Forum Moderator

krswen
Posts: 4
Joined: Mon Dec 21, 2009 7:35 am

Post by krswen » Sat Dec 26, 2009 2:55 am

I am THRILLED, Russ! Opened my G940 this morning, hooked everything up, calibrated and installed FSForce. Took off from KSEA in the Piper cub, felt the pavement strips, tried a stall & got buffet and landed (badly) and felt the tire impacts.
The moderators at Logitech highly recommend your product for FSX, and they are right.
Just sent payment for the license.
Nice job! Have a pleasant holiday.

krswen
krswen

RussDirks
Site Admin
Posts: 696
Joined: Sat Sep 13, 2003 1:18 pm
Location: Chilliwack, Canada

Post by RussDirks » Sat Dec 26, 2009 9:39 am

That's awsome. Hopefully my G940 will be arriving any day now.
Russel Dirks
Forum Moderator

garymc
Posts: 2
Joined: Sun Dec 27, 2009 6:00 pm
Location: Adelaide, Australia

FS Force makes a huge difference to G940

Post by garymc » Sun Dec 27, 2009 6:09 pm

Hi
Just wanted to say how relieved I am with what FS Force has done with my G940 and FSX. Before FS Force I was fighting with the stick forces and now the force feedback actually makes sense. So glad I came across this program.

I reckon Logitech should get you on their team! Now if only we could get you to write a similar program for a couple of other flight sims I can think of...

crim3d
Posts: 32
Joined: Wed Apr 15, 2009 7:35 pm

Post by crim3d » Mon Jan 04, 2010 4:57 pm

RussDirks wrote:That's awsome. Hopefully my G940 will be arriving any day now.
Great. Looking forward to your review.

garymc
Posts: 2
Joined: Sun Dec 27, 2009 6:00 pm
Location: Adelaide, Australia

Trim wheel setup for G940

Post by garymc » Thu Jan 07, 2010 7:14 am

In case anyone else is wondering, I found that the following line inserted into FSForce.cfg will activate the Trim Wheel 1 on the G940 joystick.

TrimWheel=Joystick:0:RzAxis

Works the elevator trim like a treat. Am using FSX SP2 under Win 7 64 bit.

krswen
Posts: 4
Joined: Mon Dec 21, 2009 7:35 am

Post by krswen » Sun Feb 07, 2010 8:06 am

hmm, where is the fsforce.cfg file located?

krswen
krswen

krswen
Posts: 4
Joined: Mon Dec 21, 2009 7:35 am

Post by krswen » Sun Feb 07, 2010 8:10 am

Found it.

krswen
krswen

heimue
Posts: 3
Joined: Sun Apr 11, 2010 8:40 pm
Location: Berlin, Germany

Re: Trim wheel setup for G940

Post by heimue » Sun Apr 11, 2010 8:51 pm

garymc wrote:In case anyone else is wondering, I found that the following line inserted into FSForce.cfg will activate the Trim Wheel 1 on the G940 joystick.

TrimWheel=Joystick:0:RzAxis

Works the elevator trim like a treat. Am using FSX SP2 under Win 7 64 bit.
I'm using the same TrimWheel option for my G940. But I recognized that the buttons 3 and 4 remain assigned to trim up and down.
Is it possible to assign these two button to the defaut button assignment from FSX?

Thanks, heimue

RussDirks
Site Admin
Posts: 696
Joined: Sat Sep 13, 2003 1:18 pm
Location: Chilliwack, Canada

Post by RussDirks » Mon Apr 12, 2010 11:56 am

I updated the help files a little while ago to include information for the G940. It's located here, near the end of the page. There's also a section there about assigning trim to buttons other than 3 and 4.
Russel Dirks
Forum Moderator

heimue
Posts: 3
Joined: Sun Apr 11, 2010 8:40 pm
Location: Berlin, Germany

Post by heimue » Tue Apr 13, 2010 2:27 am

Thank you for this quick reply, but I tried to setup a something different.
I already assigned the trim up and down option to the trimwheel of the joystick according to the help file - and that works fine.
What I want to do now is disable the default assignment of buttons 3 and 4 (so that FSX has the same behaviour as without using fs force 2 regarding those two buttons).
Is that possible?

Thanks, heimue.

RussDirks
Site Admin
Posts: 696
Joined: Sat Sep 13, 2003 1:18 pm
Location: Chilliwack, Canada

Post by RussDirks » Wed Apr 14, 2010 12:07 pm

heimue: There's no way to disable the joystick trim buttons, but you can assign the trim commands to buttons that don't exist (you can use button numbers up to 32), and then that frees up buttons 3 and 4 for other use within FSX.
Russel Dirks
Forum Moderator

heimue
Posts: 3
Joined: Sun Apr 11, 2010 8:40 pm
Location: Berlin, Germany

Post by heimue » Thu Apr 15, 2010 4:11 am

Thank you, that was the option I was looking for!
I just purchased fs force 2 - great add-on and great support!

heimue

Post Reply